antique Sewing machine treadle PMZ Class 1 - A, issue 1952

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

antique Sewing machine treadle PMZ Class 1 - A, issue 1952:
$349.00

Sewing machine treadle PMZ Class 1 - A, issue 1952This manual is suitable for all lockstitch machines PMZ plant them. Kalinin with hand and foot operated, until the last models produced electric .Text of the left almost unchanged , in its original wording plant PMZ .PMZ sewing machine :Sewing machine PMZ Class 1 -A1. Screw for adjusting the pressure of the foot. 2 . Take-up lever . 3 . Bint fastening front cover. 4 . Front cover . 5 . Nut for adjusting the tension of the upper thread . 6. Regulator thread take-up spring. 7. Thread take-up spring . 8. Washer tension . 9. Threader . 10 . Thread cutter . 11. The presser foot. 12. Screw of the presser foot . 13. A pocket part of the needle plate. 14. Engine tissue ( rake) . 15. Throat plate . 16. Platform . 17. Winder spool pin . 18. Regulator tension winder . 19. Iglovoditelya.20 rod . Igloderzhatel.21 . Screw fastening igloderzhatelya.22 . Iglovoditelya.23 threader . Mashiny.24 sewing foot . Mashiny.25 sleeve garment . Rukava.26 spool pin . Latch motalki.27 . Mahovik.28 . Winder pulley . 29. Motalki.30 spindle . Friction vint.31 . Cover strochki.32 regulator . Control lever forward and reverse stitching. 33. Adjuster screw line.
Purpose Sewing Machine PMZ
1. The machine has a centrally - bobbin shuttle.2 . The greatest number of revolutions per minute - 1200 .3 . Step greatest lines - 4 mm .4 . Submission of material in both forward and reverse .5 . Flat bed size 371 x 178 mm . 6. Head weight machines ( without manual) - 11.5 kg .
2 . PMZ sewing machine . General operating rules
1. Handwheel according to the instructions should rotate only in one direction - to the working person . The machine can not be rotated in the opposite direction ( pull) , as this may cause entanglement of yarn in the hook .2.When the machine does not work , push foot should be lifted .3.Do not let the car in motion without fabric under the presser foot planted so as not to feed dog teeth tupilis ( rack ) , and not spoil the bottom surface of the foot.4.Nelzya pull or push the fabric with your hands while sewing . You can bend or break the needle . The need to promote tissue produced by the machine .5.Vo while sewing a pocket front plate on the shuttle must be kept tightly closed.
3 . Bobbin case and bobbin sewing machine PMZ
Bobbin case and bobbin PMZIn order to replace the bobbin into the bobbin case , you must first move the front sliding plate that covers the shuttle , then two fingers of his left hand to grab the latch \"A\" and remove the bobbin case out.When you open the latch bobbin can not fall out of the bobbin case , since it delays the hook latch. To remove the bobbin , release the latch in place , turn the bobbin case with the open side down , and the bobbin is rolled out.
4 . winding the bobbin
Bobbin Winding - sewing machine PodolskFor winding the bobbin winder is a special attached to the rear of the car near the flywheel sleeve . Coiler cooperates with the lower thread tensioning device , placed on the right corner of the platform .When winding the bobbin mechanism must not operate the machine . Therefore , before embarking on a winding , you must first disable the flywheel so that it rotates completely freely , without causing movement of the mechanism of the machine. To do this, you need only turn over a large round knurled head screw friction , located in the center of the flywheel . Mounted on the bobbin winder spindle end so that the stopping pin spindle entered the slit in the bobbin.Put a spool of thread on the spool pin . Thread from the spool is pulled down , the puck tensioner. Next up on the bobbin through the hole on the left side .Bobbin PMZWinder frame in which the spindle rotates with a plastic bobbin , squeeze his hand down , so that the rubber pulley rim in contact with the surface of the flywheel.The free end of the bobbin thread need some time to hold your hand until the bobbin is not wound a sufficient number of turns to secure the end of the thread , and then terminated by the end of this . After the bobbin is fully wound , frame winder off automatically , leaving the bobbin from the flywheel .If the rubber band is not in contact with the flywheel during winding bobbin winder frame to adjust.To do this, loosen the screw in the slot winder adjusting plate , squeeze box winder down to the flywheel and hold it in this position , fasten the screw with a screwdriver in a new position on the record.With proper winding thread on the bobbin coils stacked evenly and close to each other .If winding turns uneven or irregular shape , you need to adjust the position of the bottom of the tensioner on the platform, some move the tensioner arm slot platform in the right direction . To do this , you must first release the screwdriver screw is mounted.
5 . Threading a sewing machine bobbin case PMZ
Threading in the bobbin caseWound with thread need to take two fingers of his right hand , making sure that the free end of the thread the bobbin ran from right to left .Bobbin holding his left hand in such a position so that forward slot thread on the edge of the cap was on top , and insert the bobbin into the cap.Installing the bobbin into the bobbin caseAttract the right hand thread through the slot on the left edge of the cap under the tension spring , then into a small slot at the end of the spring . The free end of the thread should be left to hang from the mounting pin cap.
6. Staging bobbin into the sewing machine
Installing the bobbinFilled bobbin thread need to put in the car. To do this, take the bobbin case by the latch with two fingers of his left hand , put it on a central rod \"H\" hook so that the finger \"K\" bobbin entered into the slot on the housing plate invoice stroke.Release latch and click on the bobbin inside until , until a lock on his central rod hook .Free end of the thread is left hanging and close the hook , closing the front plate.
7. Installing the needle in the sewing machine PMZ them . Kalinin
Installing the needle in the sewing machine PMZThe needle should be inserted at the top position of the needle bar , which is achieved by turning the handwheel . The flat side of the bulb on the tip should be to be addressed at the same time left, so outwards and the long groove of the needle blade - to the right , i.e. inwardly towards the base of the sleeve.
Pay particular attention to correct installation of the needle as the needle is mounted in the wrong PMZ sewing machine will not create a loop and will omissions.In this position, the needle is put into the needle bar \"E\" and works its way up until it stops , and then securely locked with a screw \"1\".
8. Threading the upper thread at the sewing machine PMZ
Threading the upper thread at the sewing machine PMZBefore refueling, turn of the hand wheel toward you so that the take-up lever with an eye for the thread came to the top position . Put a spool of thread on the spool pin on top of the sleeve and the thread from the spool is carried out in the following sequence:1.Vpered left through the rear left cut- thread \"1\" on the front board and down to the adjusters .2.Mezhdu washers \"2\" tension adjuster and up the tab \"3.\"3.In the ear niteprityagivatelnoy spring \"4\".4.Vverh through the eye of take-up lever \"5\".5.Vniz in thread guide \" 6\" on the front board.6.Vniz in thread guide \" 7\" on the needle bar .7.Sprava pass through the eye of the needle \" 8\" . Pay special attention to threading the needle. You need only to fill from right to left , ie outwardly .
9. Preparing PMZ sewing machine to sew products
Preparing for sewing machines PMZBefore you start sewing , you need to pull up the bobbin thread out. To do this, take the left hand by the end of the needle thread , without pulling it. Then turn over the handwheel to first needle sank into the hole of the needle plate , bobbin thread bottom captured and then rose again to its highest position.Then you need to pull the end of the needle thread and through the hole in the needle plate to pull up the lower thread .Then both ends of thread, top and bottom , pulled back and put under the foot .Planted foot is lowered to the material , and the machine is ready to sew
10 . Work on the manual typewriter PMZ
Work on the manual typewriter PMZHand drive installed and fixed rear projection sleeve located under the flywheel machine. Hand drive consists of a body of \"1\" with two toothed gears ( large and small ) , the drive arm with a lead \"2\" - for engaging with the flywheel machine and folding handle \"3\" - for the rotation of the hand .After removing the wood cabinet typewriter , pen hand drive - \"3\" is usually thrown down to the off position and leash - \"2\" disengaged from the flywheel.To bring the drive to the operating position handle \"3\" you have to turn and make a nest in the tide \"A\" on the large gear, pulling the pre- round head latch lever without which it is impossible to bring to the proper position . Place the handle , release the latch , which makes locking . Leash \"2\" need to rotate so that the leather padding entered between matches flywheel. Special latch holds the leash in the working position .Securing handwheel stroke by lowering the friction screw and on foot planted tissue , start with your right hand evenly rotate the manual drive in only one direction - from themselves . The handwheel will rotate at the same direction to a working person .
11. Work on the sewing machine foot PMZ
Foot car driven alternately pressing it socks , the heels on the bandwagon of the machine. When working correctly both legs whole foot must lie on the stretcher , and the left foot should be positioned slightly behind the right . Bandwagon machine need to pump as evenly as possible .
Driving wheel should rotate only in one direction - to the seamstress . Should beware the wrong direction of rotation , as it may become tangled in the shuttle thread .Turning machine swipe friction screw in the same manner as for the manual typewriter.
12. User PMZ . Closing sewing
Stop the car in a position where take-up lever is at the top and the needle came out of the material. Then lift the lever \"P\" , raise the presser foot , the left hand is removed from the fabric itself and cut the thread at the end of the stitching on the edge nitobrezatelya situated on top of the presser foot .For further leave sewing thread ends length of 8-10 cmUser PMZThread tension in the PMZ sewing machine is of great importance to the quality of sewing. Interweaving the top and bottom thread must take place in the middle of the cross-linkable material . Stitching on the front and on the bottom side should have the same view .If the tension of the upper thread is too high or, conversely, the thread tension is too weak , the interlacing yarn occurs on the upper side of the fabric . Machine winds above. It turns fragile and ugly seam.To eliminate this phenomenon , it is necessary to release the tension of the upper thread or lower thread tension strengthen .
If the tension of the upper thread is too weak and vice versa , the lower thread tension is too large, the interweaving threads are obtained on the lower side of the fabric - from the bottom machine winds . Seam turns fragile . In this case you need to increase the tension of the upper thread or lower thread tension ease .
Regulation upper thread tensionRegulation upper thread tension must be done with foot lowered .Tension values increases with rotation of the nut \" R\" to the right and vice versa attenuated by counterclockwise rotation . Noticing a suitable position of the pointer , you can quickly navigate to the correct installation tension .Lower thread tension is adjusted by the screw \"A\" on the spring tension of the bobbin case ( see figure above) . When turning the screw ( small screwdriver ) to the right , ie clockwise, the lower thread tension increases. When the screw is turned to the left, ie counterclockwise , the tension decreases.If the lower thread tension is set correctly , it is rarely necessary to change , in most cases a good line can be received by simply adjusting the upper thread .Too much tension can cause thread breakage .
Besides correctly selected tension , quality lines also depends on the thickness of the needle matching numbers linkable material.Sewing machine needles used number number 70, 80, 90, 100 and 110.The thicker and coarser material, the higher must be the number of needles and the lower number of threads employed , ie, a needle and thread to be thicker.Conversely, the thinner the material , the lower should be the number of the needle and above the number of threads, ie, a needle and thread to be thinner.
13. Adjusting the stitch length from the sewing machine PMZ
Adjusting the stitch length from the sewing machine PMZThe stitch length , ie the distance between the needle pricks to conventional materials provided within 1.5 - 2 mm.For thin materials line should be more likely to thick materials - less. Maximum length of stitch that you can get by car, is 4 mm .Required stitch length knob to adjust the \"B\" scale of the figures , which are deposited on the lid knob and show exemplary stitch length in millimeters. When the control lever placed on the uppermost division of the scale , extending the middle of the cover and not having the numbers, it does not feed the fabric becomes.When the machine lever \"B\" must be lowered down . The lower control arm is lowered , the less will be a line , ie, the stitch length longer . Conversely, the higher put control lever , ie, closer to the upper division of the scale , the line will be more or less than the length of the stitch .When lifting the regulator lever up from the average machine features change the feed direction is reversed , ie, when the machine will move material on working .To change the length of the stitch regulator lever needs to be translated to a new division of the scale corresponding to the desired stitch length .
Translation regulator lever on the new division is as follows.Let the governor lever \"B\" stands on any scale division and must be translated down to a larger sewing pitch . Sinking down regulator lever prevents internal restrictive plate located under the lid knob and clamping screw golovochnym left . \"A\" in the left cover arc slit .In order to be able to pull the lever below , you must first release the specified screw \"A\" and put it on the slots in the lowest position.Then place the control lever to the desired division of the scale , translate left screw \" D\" up the arc slots to stop and fix the screw \"A\".For more frequent stitch regulator lever \"B\" is translated up to the appropriate division of the scale , after which the screw \"A\" is released, transferred up until it stops , and then fixed again .
14. Reverse feed direction
PMZ sewing machine can sew in both forward and reverse direction. In the reverse direction of feed material during sewing will move in the direction of running . In order to switch the machine on a reverse , you only need to translate control lever \"B\" , which is in the lower position at a certain division of the scale, up to a stop . Stitch length , however, remains unchanged.Switching the machine to reverse flow can be performed even without stopping the sewing and removing tissue.
15. Regulation of pressure foot material
Push the tabs on the value of the material is rarely necessary to change . But when sewing silk or lung tissue may be necessary to reduce some pressing force , for which the screw is rotated by two - three turns to the left, ie, counterclockwise.When sewing thicker materials requiring a strong pressure , screw \"K\" turn two - three turns to the right, ie clockwise.Pressing the foot on the material must be sufficient to ensure uniform supply of material, and to prevent lifting of the material with a needle. Too much pressure only complicates the machine running and spoil material
16. Grease PMZ sewing machine
Grease PMZ sewing machineTo ensure easy running of the machine and prevent wear of rubbing parts of the machine all the places indicated by the arrows , should be lubricated every few drops of oil in each place when the machine is running continuously.For lubrication of hard parts in the car are the oil holes . In order to lubricate the hinge of the needle bar , you must first remove the front cover by releasing the screw fixing it .Direction for the shuttle to move the body smeared with one drop of oil. Place designated by the letter \"A\" should be lubricated when the needle is in the lowest position .