USA,Machinist,3%,Threeper,Skull,Mechanic,Engineer,Milling,Sticker,Vinyl decal

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

USA,Machinist,3%,Threeper,Skull,Mechanic,Engineer,Milling,Sticker,Vinyl decal:
$5.50

Skull,Sticker,Vinyl decal,

SIZE IS 4.5\"x6\" If you need a different size please ask.

Color will beWHITE,if not specified.

Decal is VinylCut so it will be one single color, but is available in

WHITE, BLACK,ROYAL BLUE, PINK, PURPLE.RED, HUNTERSORANGE, NEON GREEN, DARK GREEN, GOLD, and SILVER.

Please specifycolor..

The vinyl is 3MIL, resistant to Sun, Rain, Snow &Sleet.The decal will stick to any hard, smooth surface and are suitablefor wet locations (Boat, Car, Car Window, Laptop, Instrument Cases, SnowboardDecks, School Lockers, Mirrors, etc.)

An application(transfer tape) overlay allows for precise and easy placement.

All decals arecomputer cut and are customizable.

HOW TO APPLY

STEP 1:CLEAN THAT AREA GOOD!

Firstmake sure you have a dry place and no wind to install your decal.

Make sure to prep the area, this is the most important part of installing adecal! If you put your decal or sticker on a dirty surface, it will justpick that dirt and grime up like a lint roller does your shirt, those aren\'t sosticky after you use them are they! So let’s make sure the area is niceand clean so that it can adhere to where you are going to place it.
You can use soap and water, rubbing alcohol, or any other fast dryingcleaner. My favorite is rubbing alcohol since it dries by itself withinseconds and leaves no residue behind. On that note, do NOT use anythinglike Windex or other household spray cleaners that leave a residue behind or oilysubstance, that defeats the purpose and will cause your decal/sticker not toadhere to the best of it capabilities.

STEP 2:DECIDE AND PEEL!

Afteryou have cleaned your car, you now need to decide where you want to center yourdecal in the area you cleaned. I use a measuring tape to measure fromdifferent spots on the car tomake sure I have it exactly where I want it andthat it will not turn out crooked. When I measure I use a piece ofmasking tape to mark the measurements, normally four for left/right/top/bottom.Then I have a somewhat boxed area to force me to place the decal where itshould go.

Be aware after you stick it, you might cannot undo it and use it again, sinceit can separate the design or text from each other.After you decide where you want it, go ahead and start to peel your decal back,if it doesn\'t stick to the transfer tape the first pull, replace the transfertape and push it together with your fingers or use a credit card to presstogether.

STEP 3:PLACE THAT DECAL!

So youcleaned your area and also decided how and where you are going to place yournew decal or sticker and you made sure your decal can peel apart easily.

FORSMALLER DECALS -

Nowfully peel the decal off the backing and hold it on the tips of the masking/transfertape. Try not to touch the back of the decal itself since it could leavedirt on your decals back side.
You should have each hand holding the furthest corners from each other and keepit tight so that the decal does not fold in on itself. Place one end ofthe decal down and then smooth it out to the other end till the decal is fullyplaced.

FORBIGGER DECALS -

Do notfully remove the backing on your decal. You will want to remove about 1/3of the backing and start by applying that 1/3 of the decal to the car.Then slowly pull more of the backing off while at the same time apply the decalto the car until you have fully installed the decal. Either work left toright or right to left, which ever you feel best doing.
Don\'t forget you can always buy a $1 spray bottle at your dollar store, put ONEsmall drop of soap in it and fill with water and shake. Then LIGHTLY (IMEAN LIGHTLY)spray the area and then apply the decal. This is onlysuggest for bigger decals or decals that you need to be in a precise area.

STEP 3:THE HARDEST PART!

Waiting...yes this is the hardest part, because most people are so impatient that theycan\'t wait and they mess up the decal by removing the transfer tape too early!
The best way to allow your decal to dry is out in the sun, having it in theshade or in a cool place will only make it take longer. If you used amist of soapy water when installing your decal and do not let the sun dry it,then it will take a very long time before it adheres correctly, since nothingis there to remove the water and dry the decal to the surface.

Do not try and rush this buy using a heat gun, you can melt the transfer tapeand vinyl and when you peel it, it could cause the decal to stretch with thetransfer tape. Again the best way is the sun. Finally just give the decal 30 minutes before you remove the transfer tape, goinside and eat lunch. By the time you’re done you should be able to goback outside and finish your decal and be in a good mood from that great lunchand nice cold sweet tea! If your decal is still not sticking, make sureyou got it in the sun and it is warm outside, and just give it a bit longer.

After~30 minutes to dry, remove transfer paper.